Lightronics FXLD348R3I Manuel d'utilisateur télécharger pdf

Page 1 of 5

FXLD348R3I LED FIXTURE

Version 0.1 OWNERS MANUAL 02/16/2012

www.lightronics.com

Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588

FEATURES AND SPECIFICATIONS

LEDS: 48 3 Watt LEDs (tricolor 3 in 1 RGB)

Beam angle: 25 º

Control system: DMX-512

DMX channels: 3

DMX connectors: 3 pin XLR

Voltage: 120 VAC 50/60Hz

Max power consumption: 200 Watts

Size (LxWxH): 17 3/8" 12 1/4" x 8 1/4 "

Body material: Cast Aluminum

Body color: Black

Weight: 17.6 lbs

DESCRIPTION

The FXLD348R3I is a RGB LED lighting fixture. It

is suitable for stage, disco, night club, and other artistic

applications. It has several stand alone control modes,

a master/slave mode, and can operate via a DMX-512

external signal.

A double yoke enables it to be operated in several

positions.

INSTALLATION

LOCATION

The FXLD348R3I is rated IP20 and is intended for

INDOOR USE ONLY.

Locate the unit in a well ventilated area away from

moisture and heat. Holes are provided on the yokes to

install a lighting bar pipe clamp. A safety cable should

also be used.

POWER CONNECTIONS

The FXLD348R3I has a line cord for connection to a

120 VAC, 15 Amp, 60Hz, grounded service.

The safety ground pin on the power cord must be used.

DMX CONNECTIONS

A system using DMX control should be connected as a

chain of devices. In other words the control signal

cable should proceed from the controller to the first

receiving device and then to others in a continuous

"daisy chain" fashion.

The fixture has a DMX IN and a DMX OUT connector

to be used to connect the chain. The control cable

should NOT be split into a multiple run star

arrangement with a cable running from the controller

directly to each receiving device pack.

DMX CONNECTOR PIN ASSIGNMENTS

There are two different connectors which can be used

for DMX control. They are both XLR type connectors.

Some units use 3 pin connectors. Others use 5 pin

connectors. The FXLD348R3I receives a DMX signal

on the 3 pin MALE connector on the back of the unit.

The 3 pin FEMALE connector is used to connect the

next DMX device on the control chain. If your console

uses a 5 pin connector you can make up an adapter

cable to accommodate this. The table below shows the

pin assignments for BOTH the 3 pin and 5 pin

connectors.

DMX TERMINATION

A DMX chain should be terminated at the last

receiving device on the chain. This is done by

installing a commonly available 1/4 Watt, 120 Ohm

resistor across the DATA - and DATA + wires at the

IN # SIGNAL NAME

1 DMX COMMON

2 DMX DATA -

3 DMX DATA +

4 NOT USED

5 NOT USED

CAUTION

RISK OF ELECTRIC SHOCK

1 2 3 4 5 6

Résumé du contenu

Page 1

Page 1 of 5 FXLD348R3I LED FIXTURE Version 0.1 OWNERS MANUAL 02/16/2012 ww

Page 2

Page 2 of 5 FXLD348R3I LED FIXTURE Version 0.1 OWNERS MANUAL 02/16/2012 ww

Page 3

Page 3 of 5 FXLD348R3I LED FIXTURE Version 0.1 OWNERS MANUAL 02/16/2012 ww

Page 4

Page 4 of 5 FXLD348R3I LED FIXTURE Version 0.1 OWNERS MANUAL 02/16/2012 ww

Page 5

This product is warranted for a period of TWO YEARS from the date of purchase against defects in materials and workmanship. This warran

Page 6

www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588

Commentaires sur ces manuels

Pas de commentaire

Lightronics FXLD348R3I Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Lightronics FXLD348R3I. Lightronics FXLD348R3I User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Lightronics FXLD348R3I