Lightronics FXELP10 (prior to May 2009) Manuel d'utilisateur télécharger pdf

PROFILE SPOT575 USER MANUAL Page 1 of 3

V20080814

TECHNICAL SPECIFICATIONS

Power Supply: 120VAC, 60 Hz Maximum Ambient Temp.: 45 deg. C

Lamp: 575/750W Maximum Housing Temp.: (steady state): 245 deg. C

Power Consumption: 590W/760W Dimensions (L x W x H): 650 x 180 x 260mm

Weight: 6kg

INSTALLATION

During the installation DO NOT TOUCH THE GLASS BULB BARE HANDED! Please follow the lamp

manufacturer's notes! Do not install lamps with higher wattage. Lamps with a higher wattage generate

temperatures the device was not designed for. Damages caused by non-observance are not subject to warranty.

During the operation, the lamp reaches temperatures of up to 800 degrees C. For the installation, you need a

120V/575W GX-9.5 lamp or 120V/750W GX9.5 lamp.

PROCEDURE:

1. Unscrew the knurled screw of the lamp housing.

2. Remove the lamp housing from the device.

3. If replacing the lamp, remove the old lamp from the socket.

4. Insert a 120V/575W GX-9.5 lamp or 120V/750W GX9.5 lamp into the lamp socket.

5. Do not operate device with opened lamp housing! Reinstall the lamp housing.

LAMP ADJUSTMENT

The lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light

performance. Strike the lamp, open the shutter and the iris, set the dimmer intensity onto 100% and focus the

light on a flat surface (wall). Center the hot-spot (the brightest part of the beam) using the 3 adjustment screws A,

B, C. Turn one screw at a time to drag the hot-spot diagonally across the projected image. If you cannot detect a

hot-spot, pull the lamp in by turning all screws A, B, C clockwise ¼ turn, one at a time, until the light is evenly

distributed. If the light is brighter around the edge than it is in the center, or if light output is low, the lamp is too

far back in the reflector. Push the lamp out by turning the screws A, B, C counterclockwise ¼ turn

, one at a time,

until the light is bright and evenly distributed.

FOCUSING

1. Loosen the focus button on the underside of the device.

2. Adjust the focus by sliding the lens housing forward or backward.

3. Tighten the focus button.

POWER CONNECTIONS

DANGER RISK OF ELECTRIC SHOCK

The electric connection must only be carried out by a qualified electrician!

In order to connect the device to the mains, you have to install a power plug connector.

Wiring for the power cable connector is as follows:

Wire Color Function International

Brown Live L

Blue Neutral N

Yellow/Green Earth

1 2 3 4

Résumé du contenu

Page 1 - V20080814

PROFILE SPOT575 USER MANUAL Page 1 of 3 V20080814 TECHNICAL SPECIFICATIONS Power Supply: 120VAC, 60 Hz Maximum Ambient Temp.: 45 deg. C

Page 2

PROFILE SPOT575 USER MANUAL Page 2 of 3 V20080814 The earth has to be connected! Connect the device to the mains with the power plug.

Page 3 - CAUTION

PROFILE SPOT575 USER MANUAL Page 3 of 3 V20080814 KEEP DRY This fixture is intended for INDOOR USE ONLY. Do not expose this fixtur

Page 4 - V20080812

V20080812

Commentaires sur ces manuels

Pas de commentaire

Lightronics FXELP10 (prior to May 2009) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Lightronics FXELP10 (prior to May 2009). Lightronics FXELP10 (prior to May 2009) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Lightronics FXELP10 (prior to May 2009)